Husqvarna Viking Service and Repair: Husqvarna Viking

Showing posts with label Husqvarna Viking. Show all posts

Monday, June 23, 2014

Husqvarna 2000 service and repair

Husqvarna 2000 service and repair tips. Removing covers, sewing foot repair and general repair tips

The needle position not aligning could be because your machine needs a good clean and oiling. I’m not sure if your model have a button hole function. Make sure it is not engaged. Sometimes the shaft where the reverse unit turns in get sticky and does not return with your button hole dial. You will have to oil and warm it up with a hair dryer or use a special release oil. You will get access to it by removing the side cover. It can take a while to work in the fresh oil.

Husqvarna 2000 service and repair

Sunday, March 16, 2014

Husqvarna Viking sewing machine motor brushes

Husqvarna Viking motor assembly

Husqvarna Viking sewing machine

Check both carbon brushes by removing the brush cap. The carbon brushes should be at least 50% the size of new ones. It is recommended that both the carbon brush and spring be replaced. After installing new carbon brushes dress the commutator to seat the brushes.

The Husqvarna Viking sewing machine motor noise is affected by the load and the belt tension. If the motor deviates from normal check the tension of the cog belt. When replacing carbon brushes it is important to note the model of the machine. Starting with 6460 the carbon brush holder (16) was redesigned. Once the carbon has worn the holder will not allow the carbon brush spring (13) to ride the commutator. When ordering carbon brushes it is best to use the 40 16295-01 from 6460 and later models. For earlier models use the carbon brush 41 14 934-01 which will repel from the commutator automatically when the carbon is worn.

Husqvarna Viking sewing machine motor brushes

Saturday, March 15, 2014

Husqvarna viking 2000 sewing machine gear

Husqvarna Viking Power Gear

The husqvarna viking 2000 sewing machine power gear or lower gear or gearshift is a practical future to lower the sewing machine speed. This video will show you how it operate and solve some basic problems

Husqvarna Viking 2000 sewing machine

Materials used making the Husqvarna Viking 2000 sewing machine and power gear

Most of the small details (parts) of the sewing machine are made of steel or steel alloys with different grades of tempering. However, quite a lot of the details in the mechanisms are made of die-cast aluminum. In addition, here are some details which must have good bearing properties and wear resistance, which are made of different sorts of plastic. On the subject of plastic, it is important to distinguish between the type of plastic used in design details and the type used for inexpensive packing and throw-away wrappings. The constructional plastics have completely different properties and are considerably more expensive. If a detail, e.g., a cog wheel or a programmer, is made of plastic, it must have advantages over metal – e.g., a cog gear will function more smoothly 20 and quietly; a cog gear or programmer will have more wear resistance. If the Husqvarna viking 2000 sewing machine power gear is made of metal it will wear much quicker, even when using the best special steel, as long as the properties are not changed completely by means of an 0il bath or the like. You can find the Husqvarna Viking Technical Manual at this link.

I’ve add more related videos on how to repair your Husqvarna Viking 2000 sewing machine.

Husqvarna viking 2000 sewing machine gear

Saturday, February 8, 2014

Husqvarna 2000 service and repair

Husqvarna 2000 service and repair tips. Removing covers, sewing foot repair and general repair tips

The needle position not aligning could be because your machine needs a good clean and oiling. I’m not sure if your model have a button hole function. Make sure it is not engaged. Sometimes the shaft where the reverse unit turns in get sticky and does not return with your button hole dial. You will have to oil and warm it up with a hair dryer or use a special release oil. You will get access to it by removing the side cover. It can take a while to work in the fresh oil.